1. A2C59517045 CRDI Injection Pump Spare Parts&Packaging List 

NO.	1	2	3
Picture
Name	CRDI Injection Pump Assembly	Blue Anti-Rust Bag	Lining
Description	CRDI injection pump part number: A2C59517045	Prevent CRDI injection pump from rusting	Prevent the CRDI injection pump from being damaged by external forces
NO.	4	5	6
Picture			/
Name	CRDI Injection Pump Packaging Box	CRDI Injection Pump Protective Cover	/
Description	Place the injection pump and accessories	Protect the CRDI injection pump hole from contamination and blockage	/

2. A2C59517045 CRDI Injection Pump Technical Support

2.1. Causes of  A2C59517045 CRDI Injection Pump Being Damaged

• Failure to follow the engine maintenance manual during disassembly or installation may result in damage to the CRDI injection pump.
• The fuel oil used for the vehicle does not meet the standard cause damage to the CRDI injection pump, such as: the water content in the fuel oil exceeds the standard, iron powder, aluminum powder, sulfide impurities exceed the standard, etc.
• The engine is not regularly maintained according to the engine maintenance manual (please refer to the vehicle maintenance manual for the maintenance mileage). For example, failure to replace the lubricating oil of the engine system for a long time will cause abnormal wear of the engine, excessive exhaust gas volume or a large amount of carbon deposits inside the engine. The filter is not replaced during maintenance or the replaced filter cannot reach the original filter standard. all above reasons can cause damage to the CRDI injection pump.
• The abrasion of the oil pump produces iron powder and aluminum powder enter the CRDI injection pumpand cause damage to the CRDI injection pump.
• The deformation and abrasion of fuel tank result in iron powder or aluminum powder entering theCRDI injection pump and causing damage to it.
• The CRDI injection pumpis damaged due to replacement or adjustment of the relevant parts of the CRDI injection pump. For example, the valve clearance does not meet the standard after the engine is repaired, the replacement or modification of the wiring harness connected to the CRDI injection pump fails to meet the original standard.
• The engine is overheated and overloaded for a long time working results in damage to the CRDI injection pump.
• The CRDI injection pumpwill be damaged naturally at the end of its working life.
• The CRDI injection pumpis magnetized (CRDI injection pump parts’ magnetic exceeded) causing the CRDI injection pump to not work properly.
• Before replacing the CRDI injection pump, please check the engine parts carefully according to the engine maintenance manual to avoid the CRDI injection pump being damaged again after replacement.

2.2. A2C59517045 CRDI Injection Pump Storage Standards

(1) Choose a Suitable Storage Place

The warehouse and cargo yard where the CRDI injection pumps are stored should be kept clean and dry, and away from the factory buildings that generate harmful gases and dust; do not mix with acid, alkali, salt and other substances; the storage place should have a good drainage system; the cargo yard should be flattened with gravel or furnace ash etc. to enhance the water permeability of the surface layer to keep the reservoir area dry.

(2) Strict Storage Requirements

Strict inspections should be carried out when the CRDI injection pumps are put into storage, the surface cleaning work should be done well to remove water traces, oil stains, ash and other dirt, remove the rust and do anti-rust treatment in time. Packaged CRDI injection pumps must be protected from damage.

(3) Keep The Warehouse Dry And Do Moisture-proof Work

The relative humidity is usually below 70% for the CRDI injection pumps placed in the room, and the corrosion of the CRDI injection pumps is significantly reduced.

CRDI injection pumps must be stored in the warehouse, and they are forbidden to store in the same warehouse with commodities with high water content.

(4) Reasonable Stacking

After the CRDI injection pump is exposed to rain, the corrosion rate will increase significantly. The purpose of sealing is to isolate the CRDI injection pump from rainwater and humid air, so the warehouse window should be checked in time to avoid rainwater entering the warehouse.

If the CRDI injection pump package is damaged, it should be repaired or replaced; when the package is damp, the packaging material should be dried; if the original anti-corrosion and oil applied at the factory is found to be damaged or dried up, it should be cleaned and re-applied oil in time.

3. Copyright Statement

The content of this file“A2C59517045 CRDI Injection Pump CR Series Encyclopedia“ is owned by Shenzhen Shumatt Technology Co., Ltd. and is protected by copyright law and international treaties. No part of the content in this passage may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the copyright owner. For permission requests or inquiries, please contact us via hison@shumatt.com.